How many cubic yards of asphalt in a ton.

9x6x.25=13.5 cubic feet. Now divide 13.5 by 27 ( because there are 27 cubic feet in 1 cubic yard. Still with me? Good. So 13.5/27= 1/2 or .5 cubic yards. So after talking with my local asphalt dealer he said that 1 ton of asphalt would do a pad 6x9x.25. So putting that together 1 ton of medium size asphalt will cover .5 cubic yards or 13.5 ...How to Use the Basic Asphalt Calculator. Enter the length in feet: Enter the width in feet: Enter the thickness/depth in inches: To calculate your material requirement: You need: tons of material. NOTE: This estimate is based on a mix density of 148 pounds per cubic foot.How much does a cubic yard of asphalt weigh? Standard asphalt density is 145lbs/ft3 or 2322kg/m3. The asphalt unit weight is 2243 per cubic meter. Therefore 2.4 ton of asphalt = 1 cubic meter. 1 cubic yard of hot asphalt mix weighs 2.025 tons or 4050 lbs. These measurements are approximately and therefore when you are ordering the quantity ...If this is the case then a square yard of asphalt would weigh approximately 2.05 tons. If the thickness is more or less the actual weight would vary. about 13.3 cubic feet. asphalt is about 150 lb/cubic foot. This is not a valid conversion. Cubic units is a measure of volume while square units is a measure of area.

This script helps estimate the aggregate tonnage required for a particular job. To use this calculator, enter the appropriate width, length, and thickness of this application. Click on the measuring designator for thickness in feet or inches. Then, click on either Base Rock, Drain Rock, or a Custom Density material selection.A ton of asphalt, spread to 1/2-inch thickness, covers more than 35 square yards, but does not last long. Spread to 3 inches over a properly prepared base, the same amount of material covers only 5.85 square yards, but with proper maintenance, the 3-inch cover provides a driveway lasting 20 to 30 years. Asphalt provides a cheaper option …On average, 1 ton of asphalt is roughly equivalent to about 0.7 to 0.9 cubic meters. How much is 1500 square feet of asphalt? The cost of 1,500 square feet of asphalt will depend on various factors, including the thickness of the asphalt layer, the type of asphalt mix, and local pricing. You would need to multiply the cost per square foot by ...

Tons/Cubic Yard Cost per Cubic Yard; Asphalt Millings: $8 – $12: 1.4 tons: $11 – $17 ... The standard conversion is roughly 1.4 tons of RAP per cubic yard.

One cubic yard of asphalt millings covers 80 square feet at 4 inches thick. One yard of asphalt millings weighs 1.2 to 1.6 tons. Crushed asphalt delivery cost. Crushed asphalt delivery costs $30 to $100 per truckload (8 to 20 tons). Delivery increases the cost per ton and yard by 50%, depending on the quantity and distance. Some companies offer ...245 cubic yards of debris / 30 cubic yard dumpster = 8 dumpsters. 245 cubic yards of debris / 40 cubic yard dumpster = 6 dumpsters. For the C&D debris on our example 2,000 sq. ft. house, you would likely need eight to nine 30 yard dumpster loads or six to seven 40 yard dumpster loads. This does NOT include dumpsters for the concrete foundation ...You will need to know what that load comes out to in cubic yards. You would first calculate 20 tons x 2,000 pounds per ton = 40,000 pounds. Then, you would calculate 40,000 pounds ÷ 2,700 pounds per cubic yard =14.81 cubic yards. Therefore, a 20-ton load of crushed granite will provide between 14 and 15 cubic yards of stone.A cubic yard of hot asphalt mix typically weighs 4050 pounds (2.025 tons) and covers about 108 square feet (12 square yards or 10 square meters) to a depth of 3 inches and costs between $80 and $160 per cubic yard. The weight of asphalt can vary depending on its density, which is typically measured in pounds per cubic foot (lb/ft³) or ...Asphalt has a density of around 2300-2500 kg/m3 depending on the aggregate gradation and binder percentage. Enter your specific mix density if known. Otherwise, our calculator defaults to the standard 2400 kg/m3. Step 4: Get Quantity in Metric Tons. Finally, the calculator instantly outputs the total asphalt quantity needed for your project in ...

How many tons are in a cubic yard of rock? The weight of each material will vary by each material, as due to their density's they will weigh different. The majority of our sand, gravels and decorative rocks weigh between 1.15 - 1.45 tons per cubic yard. There are outliers such as our Sunburst Rock which weighs about 1 ton per cubic yard.

Most gravel weighs 1.4 to 1.7 tons per cubic yard. See below for more common material densities. For example, let’s find the amount of gravel needed for a space that is 10 feet long, 10 feet wide, and 1 foot deep. volume = length × width × depth. volume = 10′ × 10′ × 1′ = 100 cu ft. cu yds = 100 cu ft / 27 = 3.7. weight = cu yds × ...

Calculate Asphalt Millings. Type in inches and feet of your project and calculate the estimated amount of Recycled Materials in cubic yards, cubic feet and Tons, that your need for your project. The Density of Asphalt Millings: 2,410 lb/yd³ or 1.21 t/yd³ or 0.8 yd³/t. Type in your numbers. This script helps estimate the aggregate tonnage required for a particular job. To use this calculator, enter the appropriate width, length, and thickness of this application. Click on the measuring designator for thickness in feet or inches. Then, click on either Base Rock, Drain Rock, or a Custom Density material selection.1.09 ton. You will get this result if you estimate 1,430 kg/m³ as the gravel density. Since you already know the volume, use the equation d=m/V, where d is density, m is mass, and V is volume. Don't forget to use the same units and remember that 1 cubic yard = 0.76 m³. d = m / V m = d × V m = 1,430 kg/m³ × 0.76 m³ m = 1.09 tonTons/Cubic Yard Cost per Cubic Yard; Asphalt Millings: $8 – $12: 1.4 tons: $11 – $17 ... The standard conversion is roughly 1.4 tons of RAP per cubic yard.How much does a cubic yard of concrete weigh? The concrete weight depends on its density. One cubic yard of Asphalt concrete , whose density is 140.03 lbs/ft 3 , would weigh 3781 lbs ( 1715 kg ), while the same volume of reinforced cement concrete with a density of 156.07 lbs/ft 3 would weigh 4214 lbs ( 1911.4 kg ).Suppose we have 10 tons of gravel with a density of 2500 lb/cubic yard and a thickness of 6 inches. Using the calculator, we can determine the area coverage in square yards. square_yards = (10 * 2000) / (2500 * 6) ≈ 13.33 square yards. So, 10 tons of gravel would cover approximately 13.33 square yards of area.

To use the Asphalt Emulsion calculator, enter the length of the road, the width of the road, and the specified spray rate (usually determined by your respective Department of Transportation). The calculator will provide an estimate in gallons of emulsion that will be required for your project. Length (feet) Width (feet) Application Rate.It will provide roughly 3.9 short tons for 2 cubic yards. Additionally, it will produce roughly 5.85 short tons for 3 cubic yards. How many square feet will 1 ton of asphalt cover 1.5 inches thick? 30 to 80 square feet may be covered by one ton of asphalt. 7.5 to 18 tons of asphalt, based on thickness, are required for a 2-car driveway.Jan 17, 2023 ... It is most likely that the hot mix asphalt plant would produce asphalt in minimum 1 tonne batches, therefore the purchase quantity would be 4 ... 100 Main Street. W. Collingswood Heights, NJ 08059. (856) 456-2899. TRI-STATE ASPHALT. 62 Fifth Avenue. Hawthorne, NJ 07506. (800) 867-4898. Free online asphalt calculator to help you estimate how much asphalt you need for your construction project - road, private driveway, car park, etc. Output in weight and volume: tons, tonnes, cubic yards ... Type in inches and feet of your project and calculate the estimated amount of Base Material in cubic yards, cubic feet and Tons, that your need for your project. The Density of 21AA Limestone: 2,410 lb/yd³ or 1.21 t/yd³ or 0.8 yd³/t. Type in your numbers.To determine the asphalt tonnage, you'll need to convert your cubic yards and density to tons by multiplying them together and then dividing by 2,000 (since there are 2,000 pounds in a ton). For example, if using an asphalt density of 145 PCF: 12.22 cubic yards x 145 lbs/ft³ = 1,771.9 pounds.

A common rule of thumb is that one ton of asphalt covers about 80-100 square feet at a thickness of 2 inches. Therefore, to calculate the square feet in a ton of asphalt, you would divide 80 or 100 (depending on the thickness) by 2 to get 40 or 50 square feet per inch of thickness, and then multiply that by the number of inches of …How many tons of asphalt are required for a small 20-space parking lot measuring 80 ft by 100 ft paved 4 inches thick? ... 2,000 - 2,200 pounds per cubic yard; The exact density depends on the aggregates and asphalt content percentage. Dense-graded mixes fall on the higher end of the range. Porous asphalts are less dense.

Step # 3 _ Calculate Tons Using Density: As we know like the farmer is the density of the sand is 1.3 tons/cubic yard. So, multiply the volume in cubic yards by the density to find the total weight in tons: = 6,722.22 cubic yards x 1.3 tons/cubic yard. = 8,749.89 tons.Use our asphalt calculator to figure out approximately how much hot mix asphalt you will need for your project. Call 603.527.5100 for a quote.Calculate Asphalt Millings. Type in inches and feet of your project and calculate the estimated amount of Recycled Materials in cubic yards, cubic feet and Tons, that your need for your project. The Density of Asphalt Millings: 2,410 lb/yd³ or 1.21 t/yd³ or 0.8 yd³/t. Type in your numbers.S(T) = S + (S / 10) = 0.61 + (0.61 / 10) = 0.67 cubic yards. So, for a circular area with these dimensions, we would need approximately 0.67 cubic yards of crushed stone. Remember, these calculations include a 10% waste factor to account for any errors or spillage during the project.The estimated amount of material needed is 2.98 tons. To cover the same amount of space at a depth of 6 inches, the volume will be 7.4 cubic yards and the estimated amount of material needed is 8.93 tons. The Dirt Connections Portal can help you determine how many truckloads of #57 stone you will need for your project.Asphalt installation is usually bid by the square yard, the installer will buy asphalt by the ton, and it will be delivered in a truck measured in cubic yards. Therefore, a volume/weight/area ...About Asphalt, crushed. 1 cubic meter of Asphalt, crushed weighs 721 kilograms [kg] 1 cubic foot of Asphalt, crushed weighs 45.01056 pounds [lbs] Asphalt, crushed weighs 0.721 gram per cubic centimeter or 721 kilogram per cubic meter, i.e. density of asphalt, crushed is equal to 721 kg/m³. In Imperial or US customary measurement system, the ...Use this asphalt calculator to estimate how much asphalt (tarmac) in volume (cu ft, cubic yards or cubic meters) and weight (tons or tonnes) you would need for a driveway, school yard, pavement, road, etc.. The calculator uses conventional hot mix asphalt density. Imperial (in, ft or yd, lbs and tons) Metric (cm or m, kg and tonnes) Width. Length.Since crushed stone has a unit weight of around 2700 lbs/yd³, and 1 ton is equivalent to around 2205 lbs. we can say that a ton of crushed stone is about 0.82 yd³ in volume. We obtain that value by dividing the weight in pounds by the unit weight in pounds per cubic yard: 2205 lbs / 2700 lbs/ yd³ = 0.8166 yd³ ≈ 0.82 cubic yards.

As a result, one yard of gravel is equivalent to 1.69 tons. So, in one ton of ¼ to 2-inch size wet gravel it contains 0.59 cubic yards of ¼ to 2-inch size wet gravel. 4. Sand. The density of gravel with sand is 120 lb/ft3 and in SI unit it comes around 1922.22 kg/m3. As a result, one yard of gravel equals 1.62 tons.

Calculate Fine Mason Sand. Type in inches and feet of your project and calculate the estimated amount of Sand / Screenings in cubic yards, cubic feet and Tons, that your need for your project. The Density of Fine Mason Sand: 2,410 lb/yd³ or 1.21 t/yd³ or 0.8 yd³/t. Type in your numbers.

Select Base Material. #73 Crushed Limestone. 21A Limestone. 21AA Limestone. 22A Gravel. 2A Limestone. 2RC - Modified Well Graded Aggregate. 60/40 Mix. Back Fill Mix.Type in inches and feet of your project and calculate the estimated amount of Limestone Gravel in cubic yards, cubic feet and Tons, that your need for your project. The Density of 2B Limestone : 2,410 lb/yd³ or 1.21 t/yd³ or 0.8 yd³/t. Type in your numbers.Construction Converter. Use this construction conversion tool to convert between different units of weight and volume. Please note that this type of conversion requires a substance density figure. A list of some common construction density approximations is provided below. Please enter a density figure, select a unit to convert from and to ...Convert the cubic feet to cubic yards by dividing by 27 (the number of cubic feet in a cubic yard). For example, an area of 1,000 sq. ft. with a depth of 3 inches requires a volume of 2,500 cubic feet. This equates to about 92.59 cubic yards. 4. Account for compaction. Asphalt compacted during the paving process often results in a reduction in ...This materials calculator is an effective tool to help you determine your concrete, asphalt, and aggregate needs. These materials calculator serves as an estimate only. Specific project conditions and other factors may affect these results. For best results, please consult a Tilcon Sales Professional by filling out our contact us form. Our ...Aug 10, 2023 · If this is the case then a square yard of asphalt would weigh approximately 2.05 tons. If the thickness is more or less the actual weight would vary. about 13.3 cubic feet. asphalt is about 150 lb/cubic foot. This is not a valid conversion. Cubic units is a measure of volume while square units is a measure of area. Asphalt Calculator. The tonnage calculator below returns an estimation of the amount of asphalt needed for your project, along with an approximate cost that is determined by your location and aggregate prices near you. Note: This interactive asphalt calculator expands to include more options as each section is completed.Re: formula for cubic yards asphalt to tons length x width x inches thick for asphalt mat divided by 160 equals tonnage formula Note example 100w x 75L = 7500 x 3 inches deep = 22500 divided by 160 = 140.6 tons asphalt for proposed job calculation you must however take into consideration the smoothness of the base material density of the asphalt itself ex topping, binder, intermediate mix etc ...

Multiply the length, width and depth together to get your number of cubic feet. Then multiply cubic feet by 145 to know how many pounds of asphalt you will need. Divide pounds by 2,000, the number of pounds in one ton. This will give you the number of tons of asphalt needed for your project. Of course, our calculator does this for you! How many cubic yards of crushed asphalt are in a ton? There are approximately 0.5 cubic yards in a ton of asphalt. 1 cubic yard of asphalt weighs around 4,050 pounds and 1 ton of asphalt weighs about 2,000 pounds, so, number of yards of asphalt in a ton = 2000 ÷ 4050 = 0.5 yards approx. Thus, there are 0.5 cubic yards in one ton of asphalt. Step 4: Calculate The Tons In A Yard. The last step is to divide the density in lb/yd 3 by the tons in US and metric or UK terms. If you want the US tons, you have to divide the density in lb/yd 3 with 2000 and for the UK, divide it with 2200. US Ton In A Yard For Any type of Material = density in lb per yd 3 /2000.Instagram:https://instagram. secures crossword cluehealthstream srhshawaii dates persona 5hair nation recently played Suppose we need to top the driveway with a 2,300 kg/m³ asphalt, we can calculate the total weight of the asphalt needed as follows: Weight = length * width * thickness × asphalt density. Weight = 7 meters * 6 meters × 5/100 meters * 2,300 kg/m³. Weight = 4,830 kg or 4.83 tonnes. After obtaining the required weight, we can now finally ... daishe williamscactus formerly credit plus Lbs./Cubic Foot Lbs./Cubic Yard. Estimated Tons Needed: get a quote for your next project. "*" indicates required fields. Name*. Email*. Phone Number. harbor freight burbank illinois How many tonnes of asphalt in 1 cubic feet? Use our calculator to find the equivalent in tonnes of 1 cubic feet of asphalt or of any of many other substance. ... 1 cubic yard of sal, timber in kilograms; 100 US gallons of birch, wood in kilograms; 0.5 US gallon of ash, white, wood in kilograms; Cubic meters to tonnes calculator; 0.5 cubic feet ...This calculator utilises the following formula to calculate the asphalt weight: Asphalt Weight (in pounds) = Asphalt Area (in square feet) * Asphalt Depth (in inches) / 12 * 145. The formula takes into account the area of the surface to be paved with asphalt and the desired depth of coverage in inches. The Asphalt Area is measured in square ...07/02/2023 by Smit Vyas. A ton of asphalt contains about 0.5 cubic yards per cubic yard. And a cubic yard of asphalt weighs 4,050 pounds, and 1 ton of asphalt weighs about 2,000 pounds. So the number of yards of asphalt in a ton = 2000 ÷ 4050 = 0.5 yards. Thus, one ton of asphalt contains 0.5 cubic yards. If you want to calculate the weight of ...